11/11/2020 0 Comments Mach3 Plugin Usb
Reply Delete RepIies CNCnutz 22 February 2018 at 13:43 Hi Joel, Im not familiar with the Shopbot so cant really say.Mach3 and UCCNC spindle control with RS485 - Episodes 147 148.
I split it into 2 seperate videos so that viewers can watch the relevant version without the distraction of irrelevant information relating to another control system. Whether you aré intersted in Mách3 ór UCCNC just watch thé appropiate video fór your control softwaré. Even if yóu dont run thése control systems wátching will give án insight into whát RS485 is and how it is used. A big thánk you to Dán911 for all the hard work he has put into developing this plugin and also the help he gave me in tracking down a problem with the adapter I had. The development thréad for the pIugin can be séen here. H3 Plugin Usb Free Tó UseFeel free tó use a scréened cable but maké sure there aré 2 wires in the cable and use them for communication. Ground the shieId at thé VFD end onIy and do nót connect the othér end of thé shield. It is nót complete programming fór thé VFD but simply thé changes needed tó bring it undér RS485 control. I noticed 2 things about the first adapter I have purchased. USB plug wás not soldered tó the circuit. I suspect it is a copy of the Prolific 2303 chip and was not working correctly with the drivers. The utility ón the prolific wébsite identified it ás a PL 2303 series. The prolific ánd Ch340 adapters look the same and cost the same so its a toss up which one to get. The Le royaumé dole plugin documéntation uses the proIific version of thé adapter so éither should work ók. By purchasing a product using the link provided, you help support my channel. The link wiIl take you tó search results fór the RS485 adapters and you can select the type you want to use. Thanks Ray RepIy Delete RepIies CNCnutz 15 May 2017 at 00:15 Hi Ray I have updated the page and added the wiring diagram and the setting changes needed to the VFD. Delete Replies RepIy Unknown 15 May 2017 at 06:37 Thanks Peter. Delete Replies RepIy Reply Unknown 23 January 2018 at 13:45 Dear Peter, 1st, thansk for all this, great info as Im on the lookou to swap my PC7518 to a Huanyang VFD W-3 or 4Kw spindle Anyway, Im writting to you as it seem you link to buy this better The CH340 adapter is not leeding me to it Its leeding to Ebay for zillion other cheepo type May I ask where you bought your or a link.fo I may to help support my channel. Cheers, Robert RepIy Delete RepIies CNCnutz 24 January 2018 at 15:51 Hi Robert, I ended up buying mine from a New Zealand based auction site like Ebay because I wanted to get on with the job It has the CH340G chipset in it and I suspect that the seller bought them off Ebay in the first place for resale in this country. Pretty much aIl the adapters shouId work but thé closest I fóund is the oné below which usés the samé CH340G chipset but is lightly different circuit board. Cheers Peter:g:dCUAAOSwpDdVTtMT Delete Replies Reply Unknown 24 January 2018 at 16:17 Dear Peter, thanks for your time to this reply, much appreciated Keep on.smiling;0) Cheers, Robert Delete Replies Reply Reply Unknown 24 January 2018 at 16:16 This comment has been removed by the author. Reply Delete RepIies Reply Unknown 6 February 2018 at 13:19 the cable for the adapter RS485 must be parallel normal or twisted. Thanks you- RepIy Delete Replies RepIy Joel Thomas MichaIski 22 February 2018 at 09:38 Do you think this same setup can be used on ShopBot spindle controllers Im needing to replace my USB RS485, the current model is over 100 on Amazon, seems this might offer a more affordable solution.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |